Nissan Np300 / VG30 2WD Tie Rod End Set Outer 99-22
NewAftermarket

Nissan Np300 / VG30 2WD Tie Rod End Set Outer 99-22

SKUNISNP3TRE001
In stock
R319per each

Choosing the right Nissan Np300 / VG30 2WD Tie Rod End Set Outer 99-22 starts with matching the vehicle application, axle position and component specification. The product information identifies Nissan NP300, chassis VG30, 1999–2022; confirm the remaining details against the vehicle before purchase.

What this part does

Within the suspension system, this tie rod end helps transfer steering-rack movement to the wheel steering arm. Its condition can influence how loads and movement are controlled at the wheel, which is why accurate position and application are important.

How it works

The operating principle is straightforward, but fitment is vehicle-specific. its joint allows steering movement while the rod transmits the rack’s push and pull to the wheel. Check that the mounting points, joint type and orientation agree with the removed part before installation.

Product details

Product name: Nissan Np300 / VG30 2WD Tie Rod End Set Outer 99-22

Part number: NISNP3TRE001

Read the identifiers as stated, not as a guarantee of universal fit. The part number is useful when checking the correct side, design and vehicle revision with Morris Garage. Product name identifiers include 2WD.

No additional dimensions or technical attributes are stated in the product information. Compare the original part and use the VIN to confirm details that are not listed.

Vehicle fitment

The product name does not establish every mounting position or vehicle variation; compare the original component before ordering.

Application indicated: Nissan NP300, chassis VG30, 1999–2022. The make and model are supported by the vehicle category; the stated product text also identifies the details shown above. No chassis code or engine is added unless it appears in the product information. Verify exact fit using the VIN, especially where trims, production dates or drivetrains differ.

Signs the part may need attention

Possible warning signs include Steering looseness, wandering, uneven tyre wear, a knock over bumps or measurable joint play should be checked. Steering symptoms need a proper inspection; wheel alignment alone will not correct a worn joint. They can also result from other faults; inspect the complete assembly rather than treating one symptom as proof that this part has failed.

Installation and maintenance guidance

Before installation, compare the old and new parts for side, axle position, length, mounting type, thread and included hardware. Follow vehicle-specific service information and use the correct tools and torque values; do not estimate tightening values. Suspension work can involve loaded springs and components that affect steering or wheel control, so have a suitably equipped technician perform the job when needed. Replace paired components together only when inspection or manufacturer guidance calls for it. Once fitted, check fasteners, clearances, boots and routing, then arrange wheel alignment whenever steering or geometry has been disturbed. Recheck for noise or abnormal movement after the initial drive.

Before you order

Before you order, compare the replacement with the removed part and check:

  • Make, model, production year and VIN; confirm chassis or engine only where documented.
  • Front/rear and left/right orientation.
  • Mounting points, joint or bush design, dimensions, threads and any included bearing or hardware.
  • Whether the product is sold individually or as a pair, where that is stated in the product name.
  • The condition of adjoining suspension and steering parts and the cause of the original fault.

Do not assume that bolts, bushes, bearings or related components are included unless they are explicitly identified. If any detail differs, pause and confirm the application with the VIN.

Frequently asked questions

How can I confirm it fits?
Match the product identifiers and stated position with your vehicle details. Send the VIN or registration details to Morris Garage if anything is uncertain.

Does the product include other parts?
Only items expressly named in the product information are confirmed. Check whether the part is sold individually or as a pair and whether separate mounts, bearings or fasteners are needed.

Should I replace related parts at the same time?
That depends on inspection findings and vehicle-specific service guidance. Ask a qualified technician to assess the connected components and follow the vehicle maker’s instructions.

Need help confirming fitment?

Send your VIN or registration details and the part number to Morris Garage on WhatsApp 050 012 2247, call 012 012 5132, or use the Find My Part page to check fitment before ordering. Free delivery is available on orders of R1,000 and above; confirm delivery details at checkout.

1
WhatsApp
Enquire about this part →
ConditionNew
ClassificationAftermarket
Vehicle makeNissan
Side—
Position—
Selling uniteach
Stock sourceYard stock

Quick facts

TypeTie Rod Ends & Steering Racks
Vehicle makeNissan
SKUNISNP3TRE001
PriceR319
StockIn stock
ConditionNew
DeliveryR75 under R1000, free from R1000
Returns7 days standard

Vehicles it fits

These vehicle applications are stated by our supplier. We never treat a matching brand as proof of fitment — confirm with your VIN before you pay.

MakeModelYearsStatus
NissanGeneral—Listed by supplier

FAQs

Is this part in stock?

Yes, it is listed as in stock. It is R319.

How much is delivery?

Delivery is R75 under R1 000 and free from R1 000. We ship every day before 10:00.

What is the return period?

Standard returns are 7 days. Used parts carry a 3-month guarantee.

Where can I collect?

Collect at 199 Stormvoel Road, Eastlyne, Pretoria (0186) or 173 Lynn Road, Karen Park, Pretoria (0182). Mon–Fri 08:00–17:00, Sat 08:00–13:00, Sun closed.

Customer reviews

Reviews are only shown from genuine, paid purchases. None yet for this part — we don't fabricate ratings.