Nissan Murano 2 Lower Control Arm Left 09-14
NewAftermarket

Nissan Murano 2 Lower Control Arm Left 09-14

SKUNIMU09CA002
In stock
R2 559per each

For Nissan Murano, 2009–2014, this Nissan Murano 2 Lower Control Arm Left 09-14 is described with the position and other identifiers shown below. Those details matter: a similar-looking suspension part may differ by side, mounting, dimensions or vehicle revision.

What this part does

Within the suspension system, this control arm helps locate the wheel relative to the chassis while allowing controlled up-and-down suspension travel. Its condition can influence how loads and movement are controlled at the wheel, which is why accurate position and application are important.

How it works

The operating principle is straightforward, but fitment is vehicle-specific. its pivots and ball-joint connection guide wheel movement; the exact arrangement depends on the vehicle. Check that the mounting points, joint type and orientation agree with the removed part before installation.

Product details

Product name: Nissan Murano 2 Lower Control Arm Left 09-14

Part number: NIMU09CA002

Read the identifiers as stated, not as a guarantee of universal fit. The part number is useful when checking the correct side, design and vehicle revision with Morris Garage. Product name identifiers include Lower, Left.

  • Position stated: lower, left

Vehicle fitment

The product name identifies its location as lower, left. Check that orientation against the vehicle and removed part.

Application indicated: Nissan Murano, 2009–2014. The make and model are supported by the vehicle category; the stated product text also identifies the details shown above. No chassis code or engine is added unless it appears in the product information. Verify exact fit using the VIN, especially where trims, production dates or drivetrains differ.

Signs the part may need attention

Possible warning signs include Clunks over bumps, vague steering, uneven tyre wear, visible play or a damaged arm or joint are reasons for inspection. A bent arm, worn bush or failed joint can affect alignment and safe control. They can also result from other faults; inspect the complete assembly rather than treating one symptom as proof that this part has failed.

Installation and maintenance guidance

Before installation, compare the old and new parts for side, axle position, length, mounting type, thread and included hardware. Follow vehicle-specific service information and use the correct tools and torque values; do not estimate tightening values. Suspension work can involve loaded springs and components that affect steering or wheel control, so have a suitably equipped technician perform the job when needed. Replace paired components together only when inspection or manufacturer guidance calls for it. Once fitted, check fasteners, clearances, boots and routing, then arrange wheel alignment whenever steering or geometry has been disturbed. Recheck for noise or abnormal movement after the initial drive.

Before you order

Before you order, compare the replacement with the removed part and check:

  • Make, model, production year and VIN; confirm chassis or engine only where documented.
  • Front/rear and left/right orientation; this item is identified as lower, left.
  • Mounting points, joint or bush design, dimensions, threads and any included bearing or hardware.
  • Whether the product is sold individually or as a pair, where that is stated in the product name.
  • The condition of adjoining suspension and steering parts and the cause of the original fault.

Do not assume that bolts, bushes, bearings or related components are included unless they are explicitly identified. If any detail differs, pause and confirm the application with the VIN.

Frequently asked questions

How can I confirm it fits?
Match the product identifiers and stated position with your vehicle details. Send the VIN or registration details to Morris Garage if anything is uncertain.

Does the product include other parts?
Only items expressly named in the product information are confirmed. Check whether the part is sold individually or as a pair and whether separate mounts, bearings or fasteners are needed.

Should I replace related parts at the same time?
That depends on inspection findings and vehicle-specific service guidance. Ask a qualified technician to assess the connected components and follow the vehicle maker’s instructions.

Need help confirming fitment?

Send your VIN or registration details and the part number to Morris Garage on WhatsApp 050 012 2247, call 012 012 5132, or use the Find My Part page to check fitment before ordering. Free delivery is available on orders of R1,000 and above; confirm delivery details at checkout.

1
WhatsApp
Enquire about this part →
ConditionNew
ClassificationAftermarket
Vehicle makeNissan
Side—
Position—
Selling uniteach
Stock sourceYard stock

Quick facts

TypeControl Arms & Ball Joints
Vehicle makeNissan
SKUNIMU09CA002
PriceR2 559
StockIn stock
ConditionNew
DeliveryFree from R1000 (this part qualifies)
Returns7 days standard

Vehicles it fits

These vehicle applications are stated by our supplier. We never treat a matching brand as proof of fitment — confirm with your VIN before you pay.

MakeModelYearsStatus
NissanGeneral—Listed by supplier

FAQs

Is this part in stock?

Yes, it is listed as in stock. It is R2 559.

How much is delivery?

Delivery is R75 under R1 000 and free from R1 000. We ship every day before 10:00.

What is the return period?

Standard returns are 7 days. Used parts carry a 3-month guarantee.

Where can I collect?

Collect at 199 Stormvoel Road, Eastlyne, Pretoria (0186) or 173 Lynn Road, Karen Park, Pretoria (0182). Mon–Fri 08:00–17:00, Sat 08:00–13:00, Sun closed.

Customer reviews

Reviews are only shown from genuine, paid purchases. None yet for this part — we don't fabricate ratings.

Related parts

Haval Jolion front shock absorber
Used
Sample
Left (driver)
Haval Jolion Front Shock Absorber — Left

Shock Absorbers · Used

In stock
R950