Kia Rio 4 11-17 / Kia Cerato 3 13-16 Front Stabilizer Link L=R
NewAftermarket

Kia Rio 4 11-17 / Kia Cerato 3 13-16 Front Stabilizer Link L=R

SKUKIR4SL001
In stock
R329per each

The Kia Rio 4 11-17 / Kia Cerato 3 13-16 Front Stabilizer Link L=R is associated with Kia, Rio 4 11-17, 2011–2017 and the application notes below. Check the stated side, location and measurements against the original part, since suspension designs can change within a model range.

What this part does

In everyday driving, a stabiliser link matters because it connects the anti-roll bar to the suspension and helps limit body roll through a turn. A worn or incorrectly matched component can affect comfort, noise, tyre contact or steering feel, depending on its job.

How it works

In service, the part experiences repeated movement and load. as the left and right sides of the suspension move differently, the link transfers load to the anti-roll bar. Its condition and the condition of connected pieces influence handling, noise and service life, so investigate the original cause of failure.

Product details

Product name: Kia Rio 4 11-17 / Kia Cerato 3 13-16 Front Stabilizer Link L=R

Part number: KIR4SL001

Read the identifiers as stated, not as a guarantee of universal fit. The part number is useful when checking the correct side, design and vehicle revision with Morris Garage. Product name identifiers include Front.

  • Position stated: front, left or right

Vehicle fitment

The product name identifies its location as front, left or right. Check that orientation against the vehicle and removed part.

Application indicated: Kia, Rio 4 11-17, 2011–2017. The make and model are supported by the vehicle category; the stated product text also identifies the details shown above. No chassis code or engine is added unless it appears in the product information. Verify exact fit using the VIN, especially where trims, production dates or drivetrains differ.

Signs the part may need attention

Pay attention to A repetitive rattle over small bumps, clunks during cornering or visible looseness at a joint can point to wear. Inspect the bar bushes and mounting points as well; similar noises can come from other components. These clues are not conclusive on their own. A proper check of the mounting points, connected components and vehicle geometry can help identify the actual cause.

Installation and maintenance guidance

Before installation, compare the old and new parts for side, axle position, length, mounting type, thread and included hardware. Follow vehicle-specific service information and use the correct tools and torque values; do not estimate tightening values. Suspension work can involve loaded springs and components that affect steering or wheel control, so have a suitably equipped technician perform the job when needed. Replace paired components together only when inspection or manufacturer guidance calls for it. Once fitted, check fasteners, clearances, boots and routing, then arrange wheel alignment whenever steering or geometry has been disturbed. Recheck for noise or abnormal movement after the initial drive.

Before you order

Before you order, compare the replacement with the removed part and check:

  • Make, model, production year and VIN; confirm chassis or engine only where documented.
  • Front/rear and left/right orientation; this item is identified as front, left or right.
  • Mounting points, joint or bush design, dimensions, threads and any included bearing or hardware.
  • Whether the product is sold individually or as a pair, where that is stated in the product name.
  • The condition of adjoining suspension and steering parts and the cause of the original fault.

Do not assume that bolts, bushes, bearings or related components are included unless they are explicitly identified. If any detail differs, pause and confirm the application with the VIN.

Frequently asked questions

How can I confirm it fits?
Match the product identifiers and stated position with your vehicle details. Send the VIN or registration details to Morris Garage if anything is uncertain.

Does the product include other parts?
Only items expressly named in the product information are confirmed. Check whether the part is sold individually or as a pair and whether separate mounts, bearings or fasteners are needed.

Should I replace related parts at the same time?
That depends on inspection findings and vehicle-specific service guidance. Ask a qualified technician to assess the connected components and follow the vehicle maker’s instructions.

Need help confirming fitment?

Send your VIN or registration details and the part number to Morris Garage on WhatsApp 050 012 2247, call 012 012 5132, or use the Find My Part page to check fitment before ordering. Free delivery is available on orders of R1,000 and above; confirm delivery details at checkout.

1
WhatsApp
Enquire about this part →
ConditionNew
ClassificationAftermarket
Vehicle makeKia
Side—
Position—
Selling uniteach
Stock sourceYard stock

Quick facts

TypeStabiliser Links
Vehicle makeKia
SKUKIR4SL001
PriceR329
StockIn stock
ConditionNew
DeliveryR75 under R1000, free from R1000
Returns7 days standard

Vehicles it fits

These vehicle applications are stated by our supplier. We never treat a matching brand as proof of fitment — confirm with your VIN before you pay.

MakeModelYearsStatus
KiaGeneral—Listed by supplier

FAQs

Is this part in stock?

Yes, it is listed as in stock. It is R329.

How much is delivery?

Delivery is R75 under R1 000 and free from R1 000. We ship every day before 10:00.

What is the return period?

Standard returns are 7 days. Used parts carry a 3-month guarantee.

Where can I collect?

Collect at 199 Stormvoel Road, Eastlyne, Pretoria (0186) or 173 Lynn Road, Karen Park, Pretoria (0182). Mon–Fri 08:00–17:00, Sat 08:00–13:00, Sun closed.

Customer reviews

Reviews are only shown from genuine, paid purchases. None yet for this part — we don't fabricate ratings.