
Control Arm-Front-Lower Right S062918
CA001This Control Arm-Front-Lower Right S062918 is identified for the exact vehicle application to be confirmed by VIN. Suspension parts can vary by production year, chassis, engine, axle and side, so use the vehicle details below as a careful starting point and confirm the exact match before ordering.
What this part does
Within the suspension system, this control arm helps locate the wheel relative to the chassis while allowing controlled up-and-down suspension travel. Its condition can influence how loads and movement are controlled at the wheel, which is why accurate position and application are important.
How it works
The operating principle is straightforward, but fitment is vehicle-specific. its pivots and ball-joint connection guide wheel movement; the exact arrangement depends on the vehicle. Check that the mounting points, joint type and orientation agree with the removed part before installation.
Product details
Product name: Control Arm-Front-Lower Right S062918
Part number: CA001
Read the identifiers as stated, not as a guarantee of universal fit. The part number is useful when checking the correct side, design and vehicle revision with Morris Garage. Product name identifiers include Front, Lower, Right.
- Position stated: front, lower, right
- Additional stated specification: brand: ['GSP']
Vehicle fitment
The product name identifies its location as front, lower, right. Check that orientation against the vehicle and removed part.
Fitment to be confirmed with your VIN. The product information does not provide a sufficiently specific make-and-model application to state one confidently. Share the VIN or registration details with Morris Garage before ordering; do not rely on appearance alone.
Signs the part may need attention
Possible warning signs include Clunks over bumps, vague steering, uneven tyre wear, visible play or a damaged arm or joint are reasons for inspection. A bent arm, worn bush or failed joint can affect alignment and safe control. They can also result from other faults; inspect the complete assembly rather than treating one symptom as proof that this part has failed.
Installation and maintenance guidance
Before installation, compare the old and new parts for side, axle position, length, mounting type, thread and included hardware. Follow vehicle-specific service information and use the correct tools and torque values; do not estimate tightening values. Suspension work can involve loaded springs and components that affect steering or wheel control, so have a suitably equipped technician perform the job when needed. Replace paired components together only when inspection or manufacturer guidance calls for it. Once fitted, check fasteners, clearances, boots and routing, then arrange wheel alignment whenever steering or geometry has been disturbed. Recheck for noise or abnormal movement after the initial drive.
Before you order
Before you order, compare the replacement with the removed part and check:
- Make, model, production year and VIN; confirm chassis or engine only where documented.
- Front/rear and left/right orientation; this item is identified as front, lower, right.
- Mounting points, joint or bush design, dimensions, threads and any included bearing or hardware.
- Whether the product is sold individually or as a pair, where that is stated in the product name.
- The condition of adjoining suspension and steering parts and the cause of the original fault.
Do not assume that bolts, bushes, bearings or related components are included unless they are explicitly identified. If any detail differs, pause and confirm the application with the VIN.
Frequently asked questions
How can I confirm it fits?
Match the product identifiers and stated position with your vehicle details. Send the VIN or registration details to Morris Garage if anything is uncertain.
Does the product include other parts?
Only items expressly named in the product information are confirmed. Check whether the part is sold individually or as a pair and whether separate mounts, bearings or fasteners are needed.
Should I replace related parts at the same time?
That depends on inspection findings and vehicle-specific service guidance. Ask a qualified technician to assess the connected components and follow the vehicle maker’s instructions.
Need help confirming fitment?
Send your VIN or registration details and the part number to Morris Garage on WhatsApp 050 012 2247, call 012 012 5132, or use the Find My Part page to check fitment before ordering. Free delivery is available on orders of R1,000 and above; confirm delivery details at checkout.
| Condition | New |
| Classification | Aftermarket |
| Side | — |
| Position | — |
| Selling unit | each |
| Stock source | Yard stock |
Quick facts
| Type | Control Arms & Ball Joints |
| SKU | CA001 |
| Price | R1 809 |
| Stock | In stock |
| Condition | New |
| Delivery | Free from R1000 (this part qualifies) |
| Returns | 7 days standard |
Vehicles it fits
These vehicle applications are stated by our supplier. We never treat a matching brand as proof of fitment — confirm with your VIN before you pay.
| Make | Model | Years | Status |
|---|---|---|---|
| Control | Arm-Front-Lower | — | Listed by supplier |
FAQs
Is this part in stock?
Yes, it is listed as in stock. It is R1 809.
How much is delivery?
Delivery is R75 under R1 000 and free from R1 000. We ship every day before 10:00.
What is the return period?
Standard returns are 7 days. Used parts carry a 3-month guarantee.
Where can I collect?
Collect at 199 Stormvoel Road, Eastlyne, Pretoria (0186) or 173 Lynn Road, Karen Park, Pretoria (0182). Mon–Fri 08:00–17:00, Sat 08:00–13:00, Sun closed.
Customer reviews
Reviews are only shown from genuine, paid purchases. None yet for this part — we don't fabricate ratings.
